Robert — Electrical Engineer

02/05/18-Present Ethos Energy, West, Houston, Texas Job Description: Electrical Engineer Job Duties: Design and perform the following technical duties needed for start up at the Hiram Clark Utility Station providing peak power to the Friendswood area: - Design, Engineer and Redline drawings necessary for commissioning of the turbine, generator, and transformer necessary for suppling power to 138KV Transmission Lines powering the Friendswood area. - Some of the area of interest is troubleshoot equipment for High Voltage (138KV) circuit breaker, Medium Voltage (13.8KV) circuit breaker, Medium Voltage (4160 V) MCC and switchgear, Low Voltage (480V) switchgear and MCC's,(208/120V) Lighting and Power Panels, and PLC equipment. - Troubleshoot Protection relays as SEL-411, SEL421, and GE Multlin relays. 09/13/17-10/26/17 Shermco Industries, West, Houston, Texas Job Description: Electrical Field Engineer Job Duties: Design and perform the following technical duties needed for restarting Chevron Philips refinery located in Baytown: - Remove old water damaged electrical equipment in 2400 V MCC, 480V MCC, 2400 V and 480V Main-Tie-Main breakers, and emergency generator controls - Add wiring and new equipment (Test Switches,SEL751 and SEL 710, Terminal Blocks, etc.) for the 2400 V MCC, 480V MCC, 2400 V and 480V Main-Tie-Main breakers and emergency generator controls. - Test equipment for the 2400 V MCC, 480V MCC, 2400 V and 480V Main-Tie-Main breakers and emergency generator controls

09/03/13-02/13/14 GE Power Generation, Houston, Texas Job Description: Electrical Engineer Job Duties: Design and perform the following technical duties needed for design, production and starting up of power generation equipment (turbine & generator controls system): 4* Support manufacturing in the installation of turbine & generator control system. Perform technical duties for complete supplier deviation and nonconformance reports. Correct and create bill of materials

06/01/08-04/23/12 Universal Pegasus, Suite #200, Houston, Texas Job Description: Project Electrical Engineer Job Duties: Design and perform the following technical duties needed for design, production and starting up of compressor stations and oil rigs for the petroleum industry: 10* Perform short circuit study, load analysis for sizing generators and incoming power requirements, cable sizing, voltage drop studies, lighting calculations, grounding studies, bill of materials, and SKM studies. 11* Create technical documents for purchasing electrical equipment. (i.e. MCC specifications, VFD specifications, UPS specifications, etc.) 12* Review and/or correct vendor documentation and drawings. 13* Perform designs, studies, technical documentations, and calculations using the latest NEC, UL, IEC, NEMA and NFPA standards

05/03/95-02/20/98 Lockheed Martin, 1,Houston, Texas. Job Description: Facility Electrical Engineering Job Duties: Perform the following technical duties needed to support testing in a thermal/vacuum test facility: 22* Programmed and troubleshoot Omron PLC circuits using hand held programmer. 23* Design and troubleshoot instrumentation circuits. 4* Used and troubleshoot regulated and unregulated DC power supplies. 5* Designed and troubleshoot electrical circuits using low and medium voltage solid state relays, switches, pushbuttons, transformers and circuit breakers. 6* Designed and troubleshoot 120/208 voltages single/three phase motor control circuits. 7* Created and update procedural documentation necessary to run electrical equipment. 8* Design & troubleshoot heating, control, and power circuit necessary to support test article applications in a thermal/vacuum condition. 9* Design and modify drawings are on AutoCAD release 14. SOFTWARE

5* Created electrical schematics from AutoCAD 2014. 6* Perform designs, studies, technical documentations, and calculations using the latest ATEX and IEC standards for hazardous (Intrinsic Safety, Flameproof, etc.) and non-hazardous locations

2012. 9* Perform designs, studies, technical documentations, and calculations using the latest ATEX and IEC standards for hazardous (Intrinsic Safety, Flameproof, etc.) and non-hazardous locations

IDM, 11616 Galayda, Houston, Texas Job Description: Software Engineer Job Duties: Design and perform the following technical duties needed for production and starting up of Generator and VFD control systems for the petroleum industry: 14* Programmed and troubleshoot Siemens PLC using Step 7 software. 15* Programmed and troubleshoot HMI screens (Siemens WinCC 2005 & 2007, Kepware Inifilink). 16* PLC programs controls drawworks, mud pumps, rotary table, top drives, traveling blocks, and auxiliary motors. 17* 09/26/98-09/28/07 National Oilwell Varco, N, Houston, Texas.. Job Description: Field Service, Test Engineer, and Project Electrical Engineer Job Duties: Design and perform the following technical duties needed for production and starting up of Generator and SCR control systems for the petroleum industry: 18* Programmed and troubleshoot Siemens PLC using Step 7 software. 19* Tested, troubleshoot, and started up Generator (480/600 Vac), SCR (750 Vdc), and AC drive control systems for and on offshore/onshore oil rigs. Control systems are used for control of the drawworks, mud pumps, rotary table, top drives, traveling blocks, and auxiliary motors. 1* Tested and troubleshoot low and medium voltage motor control centers, analog and digital AC and DC control modules, regulated and unregulated DC power supplies, switchgear, DC motors, and three phase AC generators. 2* Design and modify drawings are on AutoCAD release 2006. 02/23/98-09/26/98 Tech Power Controls Company, 10507 Fallstone, P.O. Box 722033, Houston, Texas. Job Description: Field Service and Testing Job Duties: Perform the following technical duties needed for production and starting up of Generator and SCR control systems for the petroleum and shipping industry: 20* Programmed and troubleshoot Allen Bradley PLC using AI software version 8.15. 21* Tested, troubleshoot, and started up Generator (480/600 Vac) and SCR (750 Vdc) control systems for and on offshore/onshore oil rigs and ships. Control systems are used for control of the drawworks, mud pumps, rotary table, top drives, traveling blocks, and auxiliary motors. 3* Tested and troubleshoot low and medium voltage motor control centers, regulated and unregulated DC power supplies, switchgear, DC motors, and three phase AC generators

03/17/14-10/27/15 Omron Oilfield & Marine, Houston, Texas Job Description: Electrical Engineer Specialist Job Duties: Design and perform the following technical duties needed for production and starting up of Generator and VFD control systems for the petroleum industry: 1* Perform designs, studies, technical documentations, and calculations using the latest NEC standards for hazardous (Intrinsic Safety, Flameproof, etc.) and non-hazardous locations for land rigs. 2* Created electrical schematics from AutoCAD 2015 and used Meridian for drawing approvals. Correct and create bill of materials using Macola. 3* Used SKM for short circuit and load analysis

01/04/16-08/11/17 AContact Electric Rentals, Houston, Texas Job Description: Electrical Engineer Job Duties: Design and perform the following technical duties needed for rental of transformers, switchgear, and VFD's: - Perform designs, studies, technical documentations, and calculations using the latest NEC standards for rental buildup of switchgear (low voltage and medium voltage (5/15KV)), VFD's (low and medium voltage), and transformers (low, medium, and high voltage). - Created electrical schematics from AutoCAD LT 2016 and bill of materials using Microsoft Excel. - Work with circuit breaker protection relays including SEL 351

10/15/07-05/09/08

07/05/12-08/13/13 Forum Energy Technology, Houston, Texas Job Description: Electrical Engineer Job Duties: Design and perform the following technical duties needed for design, production and starting up of drilling equipment: 7* Perform load analysis for incoming power requirements, cable sizing, voltage drop studies, bill of materials. 8* Created electrical schematics from AutoCAD 2013 and electrical equipment using Solid Works