Jonathan — Controls Engineer

ControlLogix, CompactLogix, ML1000-ML1200, Studio 5000, RSLogix 5000/500, Factory Talk View Studio ME, RSView32, KINETIX 300, PowerFlex 525-700, Motion View On Board

S7-1500, S7-1200, S7-300, TIA Portal V15, Step 7 MicroWIN), Profinet

FX Series, Q series, GX Works2, GX Developer, GT Designer, Profibus DP MR-J VFD / Motion Control

CP1L-H, CJ1G, CX Programmer, CX Designer, RS-485, RS-232 3G3JV VFD/Motion Control

IRC5 basic - advance programming

basic – advance programming

DX200 basic programming

Project Title: Welding cell for CX340 Ford´s roof frame – X247 Mercedes Benz´s roof frame Description: Sub assembly cell for roof frames with spot and arc welding applications. Client: CIE AUTOMOTIVE - PEMSA Location: Celaya, Guanajuato Technology used: Two PLC´s in master-slave configuration (ControlLogix, CompactLogix of Allen Bradley), Euchner Safety PLC, HMI (Panel View Plus 1500), Three Nachi industrial robots with mobile and fixed servo guns, Spot welding controller (WTC MEDAR 5000), Arc welding controller (Emhart DCE 1500), Turk I/O link devices, sick marking e10, motion control (Kinetix 300), Communications (Ethernet IP/TCP). Role: Control Engineer Responsibilities:  Equipment selection.  Design electrical and pneumatic engineering.  Developing control PLC programs.  Developing safety PLC program.  Developing HMI in Factory Talk View Studio.  Configuration, programming, and teaching robots.  Configuration, scheduling weld controller.  Assist to daily meetings and daily reports.  Start up and commissioning on site. Project Title: Rotary welder for assembly lines of car muffler. Description: Production line integrated of twelve machines, where the muffler is placed in a fixed clamp tooling while the machine welder that used MIG welding rotated around it. Client: Calsonic Kansei Location: Juitepec, Morelia. Technology used PLC (Mitsubishi Q series), HMI (GOT 1000), motion control (servo drive MR-J, intelligent module QD75MH1), Communications (DeviceNet and RS-485), Balluff I/O devices, weld controller (Lincoln electric power wave S350) Role: Control Engineer Responsibilities:  Design electrical and pneumatic engineering  Developing PLC program based on the customer Standard.  Developing HMI in GT Designer  Get a line output cycle time under 52 seconds.  Commissioning on site. Project Title: Welding cell with pedestals to sub-assemblies. Description: Welding cell where ABB robots nears pieces inside of pedestal that works with projection welding. Client: Magna Skoda Location: Ramos Arizpe, Coahuila. Technology used PLC (Siemens S7-1500), HMI (SIMATIC KTP), ABB industrial robot (IRC5 controller), Communications (Profinet), nut feeder, weld controller (Harms and Wende HW2000) Role: Control Engineer Responsibilities:  Developing PLC program based on the customer Standard.  Developing HMI in TIA Portal.  Configuration, programming and teaching robots.  Configuration, scheduling weld controller.  Assist to weekly meetings and reports. Project Title: Automatic loading in antifog lacquering system. Description: A Pick and place robot takes plastic cover lenses from input table, makes a cleaning with ionized air and place them on indexing table´s bases. Client: Hella Automotive (Daimler, VW, Tesla) Location: Irapuato, Guanajuato. Technology used PLC (Allen Bradley CompactLogix), Point I/O, HMI (Panel View Plus), ABB industrial robot (IRC5 controller), Communications (Ethernet IP), Safety scanner (SZ-V), vision sensor (Keyence IV-H2000ma) Role: Control Engineer Responsibilities:  Modify existing PLC program based on the customer Standard.  Developing HMI in Factory Talk View Studio ME.  Configuration, programming and teaching robots.  Assist to weekly meetings and reports.  Start up and commissioning.  Troubleshooting.  Technical support.  Training to setters and process engineers. Project Title: Automatic screwing process in assembly line. Description: A collaborative robot performs automatic screwing process in head lamps assembly line. Client: Hella Automotive (VW, Tesla) Location: Irapuato, Guanajuato. Technology used: PLC (Siemens S7-1200), HMI (SIMATIC KTP ), collaborative robot (Universal Robot UR5), Communications (Profinet), Safety scanner (SZ-V), screwing controller and feeder (Deprag AST11) Role: Control Engineer Responsibilities:  Modify existing PLC program based on the customer Standard.  Developing HMI in TIA Portal.  Configuration, programming and teaching robots.  Configuration, programming screwing controller.  Assist to weekly meetings and reports.  Start up and commissioning.  Troubleshooting.  Technical support.  Training to setters and process engineers. Project Title: Paper cutting machine refurbished. Description: Refurbished machine using a step motor to exactly cutting in paper feeding. Client: Coformex Location: Mexico City. Technology used: PLC (Omron CP1H), HMI (NS12), drive (RTA NDC series), step motor (Sanyo Danki). Role: Control Engineer Responsibilities:  Developing PLC program in CX Programmer.  Developing HMI in CX Designer.  Developing electrical engineering.  Wiring control cabinet.  Start up and commissioning.  Troubleshooting.

Universal robots- basic – advance programming. HTL, Jan 2020.

Yaskawa - DX200 basic programming, Jun 2017.

IRC5 basic - advance programming, Jun - Jul 2016.

Step 7 basic - advance, Aug - Sept 2015.

ESIME, Mexico City