Tiago — PLC Programmer

2016 - Commissiong and Start up Divider machine WP Haton in Line 2

2014- Change the Fanuc Setup for the robots work with 100% manual speed in T1

2012 - Improved process of Montana Framing to increase production to 11 for 13 jph

2011 - Enable C.I.P (Clean in Process) of Line 3 (Specialty Breads)

Germany (NRW)- 2009 - Training commissioning and dry run in palletizing and stretch hood machines

PCL Programmer at Ford LAP for new model C482/483 launch and production support.

2013 - Industrial Robots - Basic Programming in Robot Fanuc - Senai- SCS

2012 - Weld technology Stud Weld -Tucker- General Motors - SCS- SP

USA (California) - Fremont - Tesla Model 3 project September/2017 until July/2018

Talos Automation (From September/2017 to July/2018) - Automotive Industry. Duties: Rockwell PLC Programmer Performance commission, set up and programming in Rockwell Studio PLC in new B.I.W line for Model 3, including Body Sides Inner, Body Side Outers and Rear Quartes automatic Stations.Following the Tesla standard Tesla Fremont Plant, Fremont - California Hyundai Motors do Brasil Ltda (From February/2017 to August/2017) - Automotive Industry. Duties: Automation Technician Effectuated maintenance in machines and equipments of body shop production lines. Equipments like Hyundai robots, Obara and Bosch weld panels, Sca Sealler machines, using them to monitor and modify equipments to improve and correct faults of Software Step 7 from Siemens. General Motors do Brasil Ltda (From May/2011 to March/2016) - Automotive Industry. Duties: Automation Technician Effectuated maintenance in machines and equipments of body shop production lines. Equipments like ABB and Fanuc robots, Fase weld panels, Weld Tucker stud machines and PLS Sick, using them to monitor and modify equipments to improve and correct faults of Software Controllogix 5000 from Rockwell

Sodexo do Brasil Ltda (From May/2010 to May/2011) - Enterprise service provider (Food and Maintenance). Duties: PLC Programmer 2 Effectuated software programming and alterations to improve the machine's performance and reduce products and raw material's loss, using, for this, the PLC Contrologix 5000 from Rockwell. The software used to IHM is RS View Studio. Worked with Ovens, transportation lines and fermentation chamber of own manufacture, from Benier, GBT, AMF and Rademaker (Netherland) Worked inside Wickbold unity in Hortolandia - SP. Beumer Latinoamericana Ltda. (From January/2009 to May/2010) - Fabrication Enterprise (Machines and Equipments to the Cement and Petrochemichal Industry). Duties: Start up Supervisor Performed installation, start-up (Inbetriebnahme) and technical machinery palletising machines and packing pallets (Stretch Hood) for cement and petrochemical. Valeo Sistemas Automotivos Ltda. (From January/2007 to January/2009) - Fabrication Enterprise (Vehicle Starter and Alternator). Duties: Technical Maintenance Executed corrective maintenance of production process from Alternator and Starter Motors Factory. Acted in weld equipments, programming with PLC Siemens Step 7, Bosch Se 200 and 300 electric tightening Systems, basic Kuka robots programming, effectuated back up of Op7 and corrected faults in CNC Chiron and Guitti. Campinas' Factory - SP

ABB Ltda. (From April/2002 to January/2007). Machines and Equipments Manufacturer. Duties: Maintenance Supervisor Lead a team of 35 professionals (mechanicals, toolmakers, electricians, programmers and robotists in the acting, planning and interfering in corrective and preventive maintenance of the automatic lines; robots ABB manipulator, welding, sealer (mastic), tools changer, welding grippers (automatics and manuals); chain conveyors, air conveyors and production support. Elaborated reports referring to the Director Plan of Safety (prevention of actions that may cause accidents, elimination of risks that were found, risk's analysis of tasks and work permit) and to daily production, in Underbody, Body Side, Framing and Closures lines of Body Shop's building. Located at Ford Northest Industrial Complex - Camaari - BA

Renault do Brasil S/A. (From September/2001 to April/2002) - Automotive Industry. Duties: Technical Maintenance 3 Responsible for production process and maintenance of cataphoresis lines (or eletro-coat) and Mastic (Weatherstripping Line). Worked at Nissan Utilitarian Unity - Renault and Nissan - Sao Jose dos Pinhais - PR. Duties: Technical maintenance Ford Motor Company do Brasil Ltda. (From August/1992 to December/2000) - Automotive Industry. Duties: Maintenance Electrician II Responsible for electric maintenance of the Eletro-Coat sector and car Paint Shop. Ford Trucks Plant - Sao Paulo - SP. Projects Participation